 |
| |
联系人：陈建新 |
| |
手机:13801511117 |
| |
电话:0510-85950803 |
| |
邮编：214128 |
| |
网址：www.wxssh.com |
| |
邮箱：c85950803@163.com |
| |
地址：江苏无锡市滨湖区南泉镇 |
|
 |
|
|
|
|
|
|
|
| 真空均质乳化成套设备
|
真空均质乳化锅 |
洗液锅 |
水油相溶解锅 |
50L--2000LEV、CM系列真空均质乳化设备
用途：
EV、CM型系列乳化锅是我厂制造的新型真空乳化装置，该装置吸收了国内外同类产品的优点，由有关专家成功设计，结构新颖，乳化效果好，能耗小，使用可靠，锅内外抛光处理，美观大方。
EV型特点：
乳化锅乳化过程是在全密封条件下进行的，锅内物料通过下均质机的高速内循环剪切混合乳化，上刮板搅拌器在运转时产生离心作用，使四氟刮板紧贴锅壁，有效的解决了锅壁沾料问题，有效防止了灰尘和微生物的污染，乳化后的产品光亮细腻，颗粒直径最小可达3~5μm。
CM型特点：
该种型号乳化锅是在引进设备的基础上改进的，是目前国内生产中高档乳剂，膏霜类产品必备设备，设计合理、工艺先进，各项技术参数均可与国际八十年代同类产品相比美，比意大利TE-3型和日本YQ型真空均质乳化锅均质系统的剪切次数大2倍以上，物料均质后细腻均匀、光亮度特别好。该设备的均质系统采用推进挤压蜗轮剪切结构，物料由推进叶轮送至均质机，通过叶齿蜗轮（动态）和二个固定齿圈进行均质工作，当叶轮高速旋转时产生的吸力将物料先后推进挤压和蜗轮剪切达到均质目的。均质机工作时，可根据物料粘度的不同情况，关闭锅体与均质机管路之间的阀门进行内循环和外循环均质，可以保证全部物料有机会均等乳化。同时，均质机可兼作出料泵和清洗泵之用。先进的刮板搅拌器在运转时产生的离心率作用下聚四氟乙烯刮板紧贴锅壁，有效地解决了锅壁沾料问题，不留死角，理想的变频调速装置可使其转速任意无级调速。该设备在锅台上装有独特的视镜装置，配有封闭式照明灯，供操作人员随时观察物料乳化情况。整套设备加热、冷却在同一夹套内完成，夹套外设有硅酸铝保温层，层外有抛光至镜面的不锈钢装饰板，一则可节省加热、冷却时间，二则可防止操作工人烫伤，确保生产安全。
|
50-2000 l Lev, CM series vacuum homogeneous emulsifying equipment
USES:
EV, CM type emulsifying pot series is made of new type vacuum emulsification device, the device is absorbed the advantages of similar products at home and abroad by the relevant experts successful design, novel structure, good emulsification effect, small energy consumption, the use of reliable, pot inside and outside polishing processing, the beauty is generous.
EV model features:
Emulsifying pot emulsifying process was conducted under the condition of fully sealed, pot material through high speed homogenizer under cyclic shear mixing emulsifying, scraper agitator on centrifugal effect during operation, make four fluorine scraper clingy pot wall, effectively solve the problem with pan wall material, effectively prevent the pollution of dust and microorganism, after emulsification product brightness is exquisite, minimum grain diameter up to 3 ~ 5 microns.
The CM model features:
This type of emulsifying pot is on the basis of the introduction of equipment improvement, is the current domestic production of high-grade emulsion, cream products essential equipment, reasonable design, advanced technology, the technical parameters are compared with the international similar products in the eighty s the United States, than Italy TE - 3 type and Japan YQ type vacuum homogeneous emulsifying pot homogeneous system more than 2 times greater than the number of shear, uniform after homogeneous and fine material, brightness is very good. The equipment of the homogeneous system adopts forward extrusion worm gear shear structure, material is sent to the homogenizer, promote impeller by leaf tooth worm gear (dynamic) and two homogeneous fixed gear ring, will be produced when high-speed rotating impeller suction material has advance homogeneous shear extrusion and worm gear to achieve. Homogenizer, according to the different situations of material viscosity, close the pot body with homogenizer pipeline valve between inner loop and outer loop homogeneous, emulsion can ensure that all materials have equal opportunity. At the same time, the homogenizer can and make the material and cleaning pump. Advanced scraper agitator under the effects of the eccentricity running when ptfe scraper clingy pot wall, effectively solve the problem with pan wall material, leave no dead Angle, the ideal of the frequency control device can make its speed stepless speed regulation. The device on the kitchen is equipped with unique endoscopic device, equipped with enclosed lamp, observe the conditions of material emulsion for operators. A complete set of equipment for heating, cooling, at the same jacket, jacket with aluminum silicate thermal insulation layer, outside layer are polished to a mirror stainless steel decorative sheet, one can save the time of heating, cooling, second can prevent operators burns, ensure production safety. |
|
.jpg)
.gif)
.gif)